Commisioning

I. Introducing e-WG100

1. SIM card slot
2. SOS button
3. Color control screen
4. Power ON/OFF button
5. Magnetic charge zone

1. GSM network information
2. IP connection state
3. Wifi connection state
4. Remaining battery level
5. GPS indicator
6. Tilt indicator
7. No-motion indicator
8. SOS button indicator

II. Box contents

e-WG100 watch

USB charger

USB cable

Screwdriver

Spare screws and spare o-ring for SIM card slot cap

Information card

III. Charging

• Charging cycle of a completely empty battery: about 2 hours

Make sure the charging icon is displayed after a few seconds. It then disappears after 5 seconds.
While charging, it is possible to check its progress at any time by briefly pressing the power ON/OFF button.

Using the USB cable

Adjust the watch by matching the magnetic connectors on the back side with those on the USB cable.
Connect the other end of the USB cable to the USB charger and plug the charger into the mains.

Using the charging station (optional accessory)

Fit the watch by matching the magnetic connectors on the rear face with the one of the docking station.
Connect the end of the USB cable to the USB charger and plug the charger into the mains.

IV. SIM card insertion

• SIM card format: Nano SIM

1. Remove the protection from the SIM card slot
Use the screwdriver supplied with the watch and unscrew the security screw of the SIM card slot protection. Remove the protection by first lifting the end where the screw insertion hole is located.

2. SIM card insertion
Respect the direction of insertion indicated, slight press until the SIM card locks in the slot with the sound of a click.

3. Put back SIM card slot protection
Position the guard by first inserting the end opposite the screw hole. Apply enough pressure with your thumb so that the protector is fully seated at both ends.
Use the screwdriver supplied with the watch to tighten the security screw.

V. First boot

After charging the watch, remove it from its charging system and then press and hold the power ON/OFF button for at least 2 seconds.

The watch enters its initialization phase during which it checks if a software update is available and downloads it automatically.

During this initialization phase, the main screen is displayed, the watch vibrates regularly (double short vibrations) and the different phases are indicated by the symbols described below.

Step	Image
1. Waiting for connection the IP indicator should turn green after a few seconds
2. Searching for an update this step can take several tens of seconds
3. Downloading the update only if a new update is available
4. Uploading current device configuration to emerit-console server
5. Incomplete configuration notification
6. Configuration must be completed using emerit-console platform

The initialization phase ends with an incomplete configuration notification associated with long vibrations. This notification is displayed for 1 minute and can be canceled at any time by short pressing on the SOS button.

Once the first boot has been carried out, go to www.emerit-console.com to complete the configuration of the watch.

VI. Power ON / OFF

Power ON

After charging the watch, remove it from its charging system and then press and hold the on / off button for at least 2 seconds. The watch enters its initialization phase during which it checks whether:

• A new configuration is available and downloads it automatically
• A software update is available and downloads it automatically

Note that in the event that an update is downloaded, the watch will automatically restart after the download is complete and then begin its initialization phase again.

During this initialization phase, the main screen is displayed, the watch vibrates regularly (double short vibrations) and the different phases are indicated by the symbols described opposite.
The initialization phase ends with an "alert system activated" notification associated with long vibrations. This notification is displayed for 1 minute and can be canceled at any time by briefly pressing the SOS button.

Phase	Screen
Start-up
Waiting for connection This step lasts about 40 seconds
Search for a new configuration
Downloading the configuration
Downloading the update This step can last several tens of seconds
Reboot Only if an update has been downloaded
"Alert system activated" notification

Power OFF

To turn OFF the watch, briefly press the on/off button to turn on the screen, then press and hold the on/off button for at least 2 seconds until the extinction symbol appears and release the button. The watch turns off automatically after a few seconds.